Take a sharp pin or a needle and gently clean the holes by passing the needle or the pin through one to another adjacent hole and from that hole to its adjacent hole while doing this, be careful not to pop the needle or pin in the pipe attached to the top needle. The top needle in the Keurig cannot be removed, it is attached to the machine’s cover, and unlike the bottom needle, it is sharp and pointy. Top Needle In Keurig-K Duo And Its Cleaning: After placing it on the cover of the machine should be closed easily. The bottom needle basket is fixed back in the machine while fixing it, ensure the needle is towards the machine. Join both basket halves and ensure the grooves fit well in the tabs. Thoroughly clean it in the sink by running water through it. The upper half of the basket containing the needle can be cleaned by taking a pointy needle or a pin and simply cleaning the small hole present, which may get clogged by the coffee grains. Please make sure the pockets in the other half of the basket are clean by simply dusting them off and cleaning them with water. The basket consists of two parts which can be separated by twisting them. The needle placed at the bottom basket is the bottom needle which can easily be removed by applying a little pressure from the bottom with your finger as it is not a sharp or pointed needle, so a little push backward will remove it. Gently open the machine’s top cover, and you will find a K- cup and a bottom basket. Bottom Needle In Keurig – How to Clean Them? Below are some minor problems and the way how to fix them. If you don’t fix these problems properly or on time, these can adversely affect the working of your brewer. Common Problemsīesides all of the above major problems, there are some common problems that you may face while using Keurig K-Duo. In that case, replace the motor or whole unit yourself or contact Keurig Customer Care Service. However, the motor is entirely broken if you don’t hear the grinding noise and the water is not pumping properly. It happened when air stuck into the machine shake the brewer to resolve the issue. Sometimes, the brewer does not pump water but produces a grinding noise, which means the motor cannot pump the water properly. If still, the problem persists, descale your machine. Properly clean the opening with a dish towel and clean the debris. Usually, the debris builds up in the air pumps and causes the problem you can fix it by figuring out the opening from where Keurig K-Duo pumps the water. Sometimes, you may get less coffee than usual which means there is some issue with the air pumps. The air pumps pass hot water through K-cup pods and deliver your coffee into the cup. If there is a motor problem, the whole machine may be replaced. After cleaning or descaling the water pump pipe still, there is a grinding sound while the machine is on and it’s not brewing then maybe there is a problem in the motor. Gently press the pipe and do a simple water rinse. If you observe that while the machine is on but not brewing the coffee, check the pipe connected with the water reservoir and the pump maybe there is a deposition of some debris or scaling up minerals in the pipe. Remove any kink and gently remove it, allowing the water from the reservoir to flow freely in the pipe to the sensor. The other end of the pipe is connected to the outer vent, which any bug or particle can block. The machine’s back cover is removed by simply sliding it backward or applying a little force by a screwdriver to remove its tabs.Ĭheck the pipe connecting the reservoir and the sensor for any blockage or kink. If the problem is not solved, open the machine cover. Always try the simple technique to solve the issues, like first putting some water on the reservoir plunger and gently applying pressure with the thumb to remove any air bubbles. If there is any problem with the sensor, there will be an “ADD WATER” signal on the monitor when you switch on Keurig. The water reservoir is attached to the machine via two pipes, and one is attached to the water pump while the other is to the low water sensor. The low water sensor in Keurig indicates the water level of the reservoir. Some major problems associated with Keurig K–Duo are: Low water sensor: What are the major problems with Keurig K–Duo? This article has collected all the information you need to troubleshoot Keurig K-Duo. That’s where this article you’re reading comes in handy. The only problem is understanding Keurig K-Duo’s problems and how to solve them. Fixing Your Keurig: Troubleshooting Tips and Common Causes of Malfunctions
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |